Compatible with Multiple Substrates
Will Not Discolour Treated Surfaces
Low VOC Content (Low Odour, Non-Flammable)
SoluGuard Multi-Surface Biocide is a high-strength biocide for removing algae, fungi and mould growth from a wide range of surfaces. It is supplied ready-for-use in a 5 litre pack.
Treat a wide range of surfaces: internal walls, roof tiles, concrete surfaces, brick, stone, render and plastic. SoluGuard Multi-Surface Biocide can be used to remove algae from driveways, patios and ornamental stone monuments. SoluGuard Multi-Surface Biocide can be used before Stormdry Masonry Protection Cream to minimise regrowth. Clear existing biological growth from masonry surfaces and minimise future algae and lichens.
SoluGuard Multi-Surface Biocide is:
Each 5 litre pack of SoluGuard Multi-Surface Biocide treats 10 – 100 m2, depending upon the porosity of the substrate being treated. It can be applied with a brush, roller or by coarse spray. For best results use clean water and a pressure washer to clean the surface of dead growth after 72 hours.
Remove any loose mortar, dust or other surface laitance using a masonry brush. SoluGuard Multi-Surface Biocide should be applied on exterior surfaces in dry weather — ideally when no rain is forecast for the next 24 hours.
Fill the 5 litre pressure sprayer with SoluGuard Multi-Surface Biocide. Replace the pump mechanism and charge the sprayer.
Apply SoluGuard Multi-Surface Biocide in accordance with the application instructions [1]. Apply 1 litre of product per 2 – 20 m2 of surface. One 5 litre unit can cover between 10 – 100 m2. The coverage will vary depending upon the overall porosity of the substrate to be treated.
For best results, the treated surface should be cleaned after 72 hours using clean water. Where appropriate a pressure washer can be used. This will remove deposits of dead biological growth from the treated surface.
Remove any loose mortar, dust or other surface laitance using a masonry brush. SoluGuard Multi-Surface Biocide should be applied on exterior surfaces in dry weather — ideally when no rain is forecast for the next 24 hours.
Fill the 5 litre pressure sprayer with SoluGuard Multi-Surface Biocide. Replace the pump mechanism and charge the sprayer.
Apply SoluGuard Multi-Surface Biocide in accordance with the application instructions [1]. Apply 1 litre of product per 2 – 20 m2 of surface. One 5 litre unit can cover between 10 – 100 m2. The coverage will vary depending upon the overall porosity of the substrate to be treated.
For best results, the treated surface should be cleaned after 72 hours using clean water. Where appropriate a pressure washer can be used. This will remove deposits of dead biological growth from the treated surface.
[1] Refer to the SoluGuard Multi-Surface Biocide datasheet for full application guidelines. The datasheet can be downloaded in PDF format from the ‘downloads’ tab at the top of the page.
| Appearance | Clear liquid |
| Recipe Type | Liquid, water-based |
| Density | 1.0 g/cm3 |
| Size(s) & Packaging | 5 litre jerry cans |
| Coverage | 1 litre covers 2 – 20 m2. A 5 litre pack covers 10 – 100 m2[1] |
| Storage | Store above 5°C in dry conditions in original closed box. Store in a safe place, keep out of reach of children. Keep away from food, drink and animal feedstuffs |
| Shelf Life | 12 months |
| Active Ingredient(s) | Quaternary ammonium compounds (QUATS) |
| Effective Against | Moulds, algae and lichens |
[1] The coverage rate will vary depending upon the roughness and absorbency of the surface, use as a guide only.
How can we help?
Related Pages
Get it Done
Subscribe to get information about products and offers.
